Milnor KURSPK0026 Instructions d'exploitation

Naviguer en ligne ou télécharger Instructions d'exploitation pour Sèche-linge électrique Milnor KURSPK0026. Milnor KURSPK0026 Operating instructions Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 30
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Published Manual Number/ECN: HURSPK0025/99503N
• Publishing System: TPAS
• Access date: 03/06/03
• Document ECN's: Latest Available
Kit Instruction—
KURSPK0025
KURSPK0026
PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
Vue de la page 0
1 2 3 4 5 6 ... 29 30

Résumé du contenu

Page 1 - KURSPK0026

Published Manual Number/ECN: HURSPK0025/99503N• Publishing System: TPAS• Access date: 03/06/03• Document ECN's: Latest AvailableKit Instructio

Page 2 - Please Read

HURSPK0026/00186Page 1 of 21INSTRUCTIONS FOR 50 KILO AND 60 KILO PRESS SHIM RETRO-FITThese instructions are for adding shims under the main bell air c

Page 3 - ÊSetting Switches

HURSPK0026/00186Page 2 of 218. Replace the coupling onto the shaft on top of the 12 bolt-hole coupler shim.9. Evenly torque the bolts of the coupling

Page 4

HURSPK0026/00186Page 3 of 2121. Slide as many large shims in the gap between the base and cross-member as possible. If agap remains between the large

Page 5 - ËAngle of Switch

HURSPK0026/00186Page 4 of 21shaft bearing from the upper cross-member (See Figure 8).34. Loosen the two bolts that join the shaft-lock to the right-ha

Page 6

HURSPK0026/00186Page 5 of 21Reconnect the left-hand uplock jaw and shaft-lock together using the new lock-nutsprovided in the kit and the existing bol

Page 7 - ÊGeneral Safety Requirements

HURSPK0026/00186Page 6 of 2159. Repeat step (49) for the other lock segments. Record all measurements - they will beused in determining the thickness

Page 8

HURSPK0026/00186Page 7 of 21clearances (that is, the clearances which should result when the new shim thickness isadded or subtracted from the reading

Page 9 - ÊDanger From Moving Conveyor

HURSPK0026/00186Page 8 of 21Main Bell AirCylinder BoltsTrace Outline of Main Bell Air Cylinder Base on Upper Cross MemberFigure 115

Page 10

HURSPK0026/00186Page 9 of 21TorqueTo25 ft-lb(33.9 Nm)Main Dome CouplingFigure 216

Page 11

HURSPK0026/00186Page 10 of 21Downlock Shims Placed on Bedin order to Shim Main Bell Air CylinderFigure 317

Page 12

Please ReadAbout the Manual Identifying Information on the CoverThe front cover displays pertinent identifying information for this manual. Most impor

Page 13

HURSPK0026/00186Page 11 of 21One of the Four Main BellAir Cylinder BoltsFigure 418

Page 14

HURSPK0026/00186Page 12 of 21Main Bell Air Cylinder Shims19

Page 15

HURSPK0026/00186Page 13 of 21Figure 5Uplock ShaftNut and BoltRight-Hand UplockAssembly BracketAirCylinderClevisBracketClampingBoltLeft-Hand UplockAsse

Page 16

HURSPK0026/00186Page 14 of 21Figure 6Left-Hand SideLock Shaft BearingRight-Hand SideLock Shaft BearingLock Shaft Spacers21

Page 17 - Figure 1

HURSPK0026/00186Page 15 of 21Figure 7Right-Hand SideLock Shaft Bearing22

Page 18 - Figure 2

HURSPK0026/00186Page 16 of 21Upper Cross-MemberShaft Lock Uplock JawFigure 823

Page 19 - Figure 3

HURSPK0026/00186Page 17 of 21Figure 9Square Holes in the Side of the Uplock Jaw(File Paint off of the Inside surface of the Holes)24

Page 20 - Figure 4

HURSPK0026/00186Page 18 of 21Figure 10Old Setup of Dome Full-Up Contact Switch and BracketFigure 1125

Page 21 - Main Bell Air Cylinder Shims

HURSPK0026/00186Page 19 of 21New Positioning of Dome Full-Up Contact Switch and BracketDome Full-Up Contact Switch BracketDome Full-Up Contact SwitchF

Page 22 - Figure 5

HURSPK0026/00186Page 20 of 21Figure 1327

Page 23 - Figure 6

MSSM0116AE/8809BVÈSETTING LIMIT SWITCHESÊLimit Switches—Including Microswitches— Will Be Damaged If Over-actuated!Any limit switch will be damaged if

Page 24 - Figure 7

HURSPK0026/00186Page 21 of 21Figure 14Lock Ring BoltsLocation of Downlock Shims28

Page 25 - Figure 8

MSSM0116AE/8809BV (1 of 2)ÈSETTING LIMIT SWITCHESÊLimit Switches—Including Microswitches— Will Be Damaged If Over-actuated!Any limit switch will be da

Page 26 - Figure 9

ËFree Position of Rotary Lever—Attach the rotary lever to the shaft so that, in the free position, the leveris at a right angle to the direction of re

Page 27 - Figure 11

ËFree Position of Rotary Lever—Attach the rotary lever to the shaft so that, in the free position, the leveris at a right angle to the direction of re

Page 28 - Figure 12

MSOP0922AE/9805AVÈPRESS SAFETY FOR INSTALLATION AND SERVICEÊGeneral Safety Requirements(specific warnings, next page and throughout manual)Incorrect i

Page 29 - Figure 13

MSOP0922AE/9805AV (1 of 2)ÈPRESS SAFETY FOR INSTALLATION AND SERVICEÊGeneral Safety Requirements(specific warnings, next page and throughout manual)In

Page 30 - Figure 14

ÊDanger From an Operating PressCRUSH HAZARD—Devices in and above the press move without warningand can entangle, crush, or sever limbs on contact. ☞ N

Commentaires sur ces manuels

Pas de commentaire